Exterior de Industrias Relente

Technical article

Technical reading from Industrias Relente about precast moulds, pipe jacking, drilling and industrial manufacturing.

DateRelente blog

A modular precast box culvert mould covers several culvert sections (known as dalots in French-speaking countries and the Maghreb) from the same base. The frame, corners and locking system stay the same, while filler panels and joint rings are swapped. It pays off if you produce several sections in medium-sized runs. If you produce a single section in high volume, a fixed mould has fewer joints and wears less.

Precasters often ask us for one thing: «I want to cover my whole box culvert range with a single mould». Sometimes that is possible, and sometimes it is not advisable. It depends on which parts can be interchanged and on what limits the life of the mould.

What parts a precast box culvert mould has

A box culvert is a closed rectangular concrete unit laid in series to form watercourse crossings, service tunnels or underpasses. Whoever the manufacturer, its mould is almost always organised into these parts:

  • Inner core: forms the culvert opening and the haunches, the chamfers at the inside corners. It is usually collapsible or retractable so the unit can be released at demoulding.
  • Outer jacket or outer shutter: forms the outside faces. It usually opens in two or more leaves, each with its own locks.
  • Bottom ring or base ring: forms the joint at one end of the unit (the spigot and socket or whichever profile has been chosen).
  • Top ring or head ring: forms the opposite joint, the one that mates with the next unit.
  • Locks, centring guides and pins: keep everything aligned cycle after cycle.
  • Vibrator brackets and lifting points: the mould has to withstand vibration and be moved safely.

In French-speaking countries, and especially in the Maghreb, these units are known as dalots. For those who work in French, we also provide this information in French on our website, in the section on moulds for concrete box culverts and pipes.

Dimensions: how a box culvert section is defined

Each culvert dimension affects different parts of the mould:

  • Internal width (span) and internal height (rise): these are the dimensions the end client specifies for the site, and the ones that vary most within a product range.
  • Wall and slab thickness: depends on the structural design, the depth of fill and the traffic loads. It is not always the same for every section.
  • Unit length: in vertical casting, the length of the unit is the height of the mould.
  • Haunches: their size determines the design of the core corners.
  • Joint type: defines the geometry of the base and head rings.

If you are unsure whether your unit is a box culvert, a pit or a chamber, and what each type of mould can handle, we cover this in our article on the differences between box culverts, pits and chambers and the limits of their moulds, on our technical blog.

How a modular mould covers several sections

The idea behind a modular mould is simple: the expensive, precision-critical parts are built once, and whatever changes from one section to another is handled with interchangeable parts. The difficulty lies in deciding correctly what is fixed and what is interchangeable.

What stays fixed

The usual approach is to keep the corners of the core and the jacket (with their haunches), the frame, the locks, the vibrator brackets and the lifting points. These are the areas under the most stress and the hardest to manufacture accurately. If they are kept, every section in the family shares the same corner geometry.

What is interchanged

What you want to changeHow it is usually handledWhat it involves
Internal widthFiller panels on the horizontal faces of the core and the jacketEach width also needs its own joint rings, or rings designed to be adjustable
Internal heightFillers on the walls of the core and the jacketAs with width: the rings must follow the change
Wall or slab thicknessA different jacket or core, or spacers that move one away from the otherThis is the most costly change: it is best to fix the thickness for each family of sections
Unit lengthFixed-height mould, or a height extension planned from the design stageAffects vibration, weight and the crane capacity required
Joint typeA specific set of rings for each profileMixing joint types in one mould multiplies the loose parts

The limits of a modular mould

When we are asked for a mould that covers many sections, the first thing we look at is how far apart those sections are. A modular mould has physical limits that are worth knowing before you order one:

  • Every joint leaves a mark. Where a filler meets the fixed panel there is a line on the concrete, and a point where grout can leak out if the fit is poor.
  • Stiffening is sized for the largest section. If the family spans very different sections, the mould ends up heavy for the small ones or only just adequate for the large ones.
  • Every section change takes assembly time and staff who know how to do it. If you change sections often, that time comes out of production.
  • More loose parts mean more storage and a greater risk of damage or loss.

That is why, in practice, we usually propose families of closely related sections with the same thickness and the same joint, rather than a single mould for the whole range. The criteria we use to size these decisions are set out in our article on design criteria for custom precast concrete moulds, also on our technical blog.

When a modular precast box culvert mould pays off, and when a fixed one does

There is no single answer: it depends on how many sections you actually sell, how many units of each you produce and how often you change. These are the scenarios we see most often:

Precaster’s situationWhat usually pays offWhy
One section in continuous productionDedicated fixed mouldNo intermediate joints or repeated assembly: less wear and a more uniform finish
Range of closely related sections, project-based orders in short or medium runsOne modular mould per familyA single structure covers several sections without tying up several moulds that sit almost idle
Very different sections (small and large spans)Two modular families or separate fixed mouldsA single mould would be oversized for some and overstretched for others
A specific project with a large number of units of the same sectionFixed mould for that sectionThe volume justifies a mould that is not dismantled for the whole project

Before deciding, we recommend answering four questions with data from your own production, not optimistic forecasts:

  1. Which sections have you actually produced in the last year, and how many units of each?
  2. How many times a month would you need to change section?
  3. Who will carry out the changeovers, and with what lifting equipment?
  4. Do all the sections have the same thickness and the same joint, or would they need to be split into families?

What limits the service life of a modular mould

A box culvert mould works with abrasive concrete, intense vibration and daily demoulding. In a modular mould, there is also the wear from assembling and dismantling parts. These are the factors that shorten its life the most:

  • Abrasion of the contact plate: the concrete gradually polishes and wears down the faces in contact with it.
  • Vibration fatigue: the welds on stiffeners and vibrator brackets are the areas that suffer most.
  • Impacts and distortion during demoulding: forcing a jacket leaf or striking the core to release it distorts panels, which then no longer close properly.
  • Play in the interchangeable joints: holes, pins and centring guides enlarge with every assembly if they were not designed for repeated use.
  • Wear on the joint rings: the joint is where the unit has to mate with the next one, so any distortion shows up on site.
  • Aggressive cleaning and corrosion: scraping with tools that scratch the plate, or leaving concrete stuck to it, speeds up deterioration.

What extends service life is decided at the design stage

Most of a modular mould’s service life is determined before it is built: stiffening designed for the largest section in the family, joints with centring guides intended for repeated assembly, easy access for cleaning and well-placed lifting points. In daily use, it helps to clean after every cycle with tools that do not scratch, apply release agent properly and store fillers on racks rather than stacked on the floor.

For safety, demoulding and section changes must always be carried out using the designated lifting points, without forcing parts with the crane and without anyone standing under suspended loads. When a mould no longer produces units within the tolerances your project requires, or the locks no longer close properly, the sensible course is to plan a new mould and use the opportunity to correct in the design whatever has failed.

Standards: a compliant box culvert starts with the mould

The mould is not certified in its own right, but it determines whether the unit comes out within the required tolerances. In Spain, the Structural Code (Royal Decree 470/2021) governs concrete structures, including precast elements. In the European Union, Regulation (EU) No 305/2011 on construction products requires a declaration of performance and CE marking for products covered by a harmonised standard.

That is why, when we study a box culvert mould, we start from the tolerances the precaster has to meet under its product standard and its project, not the other way round. If you produce for another country, it is best to tell us from the outset which standard will apply.

What information we need to study your box culvert mould

To assess whether your case calls for a modular or a fixed mould, it helps if you send us:

  • The list of sections (internal width and height) you want to produce, ranked by volume.
  • Wall and slab thicknesses for each section, and haunch size.
  • Unit length and joint type.
  • How you vibrate and demould today (or how you plan to).
  • Planned output and how often you change section.
  • Crane capacity and available floor space.

The most common mistakes when preparing this information, such as leaving out the joint or the lifting capacity, are covered in our article on mistakes to avoid when ordering custom precast moulds, on our technical blog.

At Industrias Relente, we design and manufacture custom moulds for precast concrete at our workshop in La Lantejuela (Seville, Spain), for precasters in Spain and other countries. Our product range includes moulds for concrete box culverts and pipes. If you would like us to study which mould suits your box culvert range, get in touch with us and tell us the dimensions, intended use and operating conditions.

Frequently asked questions

What is a dalot?

It is the name used in French, and commonly in the Maghreb, for precast concrete box culverts of rectangular section. They are used for watercourse crossings under roads, service tunnels and underpasses.

Can the wall thickness be changed in a modular mould?

It is possible, but it is the most costly change, because it means replacing the jacket or the core, or adding spacers between them. The usual approach is to group sections by thickness so that each modular family shares the same one.

How many sections can a modular box culvert mould cover?

It depends on how close the sections are to one another, whether they share thickness and joint, and the stiffening the largest section allows. It is better to define families of closely related sections than to force a single mould to cover the whole range.

Keep reading

More technical criteria, organised by line of work.

The blog categories help you continue by affinity: precast moulds, pipe jacking and deep drilling tools.

Industrial blog