Exterior de Industrias Relente

Technical article

Technical reading from Industrias Relente about precast moulds, pipe jacking, drilling and industrial manufacturing.

DateRelente blog

A dry cast concrete mould for immediate demoulding is stripped as soon as the unit has been compacted: it has to be very rigid, withstand intense vibration cycle after cycle and release the fresh concrete without dragging it. A wet cast mould holds a more fluid concrete until it hardens, so what it needs is tightness, resistance to lateral pressure and demoulding by opening.

In short

  • With dry cast concrete, the unit leaves the mould while still fresh and cures outside it, standing on its pallet or base ring.
  • With fluid concrete, the unit cures inside the mould and is only stripped once it is strong enough to be handled.
  • An immediate demoulding mould is designed for vibration, wear and clean extraction in short cycles.
  • A wet cast mould is designed to avoid grout loss, resist the pressure of the concrete without deforming and open without damaging the unit.
  • One mould rarely works well for both systems: the production system is decided before the mould is designed.

What is the difference between immediate demoulding and curing in the mould?

The difference lies in when the unit leaves the mould, and that is determined by the consistency of the concrete.

With immediate demoulding, the plant works with a dry, low-water (zero-slump) concrete that is thoroughly compacted by vibration and, depending on the machine, by pressure. Once compaction is finished, the unit is cohesive enough to stand on its own: the mould is removed straight away, the unit stays upright on its pallet and the mould is filled again for the next one. A single mould produces many units in one shift.

With wet casting, the plant works with a more fluid concrete, plastic or self-compacting, which fills the mould with little or no vibration. The unit cannot be touched until it hardens, so the mould stays occupied for hours. To keep production going, one mould is needed for every unit to be produced in that cycle.

Neither system is better in the abstract: it depends on the unit, the machine the plant already has, the finish required and the volume to be produced.

Dry cast concrete mould for immediate demoulding: what it has to withstand

This is the mould that works hardest. Each cycle is short and repeated many times a day, always with intense vibration and with a dry concrete that abrades the steel plates. That is why, when we design a mould of this type, we focus mainly on four things.

Rigidity against vibration

Compacting dry cast concrete transmits strong, continuous vibration to the mould. If the outer jacket or the core flexes, the energy does not reach the concrete properly, compaction becomes uneven and the geometry varies from one unit to the next. In addition, a structure that vibrates more than it should eventually cracks at welds and stiffeners. Plate thickness, ribs and rings are sized for that specific vibration, not for the weight of the concrete.

Cores and vibrator housings

In many systems vibration is applied through the inner core. The core has to house the vibrators, transmit their energy evenly over its full height and withstand continuous work without loosening. On the page for our box culvert and pipe moulds you will see this listed as cores for vibrators, alongside the outer mould, the core and the retaining band.

Clean stripping of fresh concrete

The unit leaves the mould before it has set: any friction, snagging or suction between the concrete and the plate results in spalling, broken edges or cracks at the mouth. Contact surfaces have to be smooth and aligned, and the extraction movement has to be straight and free of shocks. Here the internal finish of the mould matters as much as its strength.

Pallets and wear

Because the unit cures outside the mould, it remains on its pallet, which gives shape to the base or the socket while it hardens. As many pallets are usually needed as there are units curing at the same time, and they all have to be identical for the units to be identical. Dry cast concrete is also abrasive, so friction areas are designed with wear in mind.

Wet cast mould: what changes in the design

Here the mould goes through fewer cycles, but it holds liquid concrete for hours. The priorities are different.

Tightness: keeping the grout in

It is one of the questions we hear most often: units with honeycombing, porous edges or fins at the joints. The cause is almost always the same: grout escapes through the joints between panels, through the closures or at the contact with the base. A wet cast mould needs well-fitted joints, closures that clamp evenly and a base that seats without gaps.

Lateral pressure of fresh concrete

Fluid concrete pushes against the mould walls like a heavy liquid, and with self-compacting concrete that pressure is usually higher, because the mould is filled in one go and the concrete stays fluid over its full height. If the walls are not rigid enough, they bulge, and the unit comes out with deformed faces even if the mould closes properly.

Demoulding by opening

The hardened unit is not pulled out: the mould is opened. Hinged or sliding sides, collapsible cores and quick-release closures allow the mould to be separated without forcing the unit. With the release agent properly applied and a shock-free opening, the cycle is clean and the plates last longer.

Comparison: what the mould needs in each system

AspectDry cast concrete, immediate demouldingFluid concrete, wet casting
When the unit is strippedAs soon as compaction ends, while freshOnce it has hardened sufficiently
Main load on the mouldIntense, repeated vibrationPressure of fresh concrete for hours
Design priorityRigidity, fatigue and wear resistanceTightness and wall rigidity
Demoulding methodStraight, clean extractionOpening the sides or collapsing the core
How many moulds are neededFew moulds, many palletsOne mould per unit in each cycle
Typical failureCracked welds and units that slump or spall when strippedGrout leakage and bulging faces

Can a wet cast mould be used to switch to dry cast concrete?

A common case: a plant producing box culverts or pipes by wet casting wants to increase output by moving to dry cast concrete with immediate demoulding, and asks whether it can keep its existing moulds. Usually it cannot. A mould built for wet casting is designed for the pressure of the concrete, not for the vibration of a machine; it has no housing for vibrators, the way it opens does not allow straight extraction of a fresh unit and there are no pallets to leave the units curing outside.

What we do in that situation is start with the system, not the mould: which machine and what vibration are involved, how the unit will be stripped, how many units have to cure at the same time and what geometry the product requires. With that, a new mould is designed for that system. The same applies the other way round: an immediate demoulding mould is not designed to hold grout for hours.

We often come across another, quieter mistake: choosing the production system after ordering the mould. If the mould is designed without knowing how the concrete will be compacted and stripped, the plant ends up adapting its process to the mould instead of the other way round. We cover this in more detail in our article on mistakes when ordering custom moulds for precast concrete.

What needs to be decided before ordering the mould?

  1. The production system: immediate demoulding with dry cast concrete or wet casting with fluid concrete.
  2. The machine and the vibration: whether vibration is applied through the core, from the outside or through the table, and how the concrete is compacted.
  3. The unit: drawing or technical sample, dimensions and service conditions of the product.
  4. The production rate: how many units per day and how many curing at the same time, which is what sets the number of moulds or pallets.
  5. Handling: how the mould is moved, how it opens and how the unit is removed in the plant.

If you want the detail of how we translate that data into plates, stiffeners and closures, we explain it in our design criteria for custom precast concrete moulds. And if your unit is a jacking pipe, its geometry and closures have their own requirements, which we cover in our pipe jacking moulds.

We design the mould for your production system

At Industrias Relente we custom-build steel moulds for box culverts, pipes and precast concrete units, starting from your drawing or technical sample and from the system your plant uses. If you are choosing between dry cast concrete with immediate demoulding and wet casting, or you are about to switch from one to the other, contact us and tell us about the dimensions, use and conditions: we will work with you on the mould your production needs.

Frequently asked questions

Can I use the same mould for dry cast and fluid concrete?

Generally not. An immediate demoulding mould is designed for intense vibration and stripping while fresh, while a wet cast mould is designed to hold grout and withstand the pressure of the concrete for hours. The recommended approach is to design the mould for the system you will produce with.

Why does dry cast concrete need pallets?

Because the unit leaves the mould before it has set and has to harden on something that keeps the shape of its base. That is why as many pallets are usually needed as there are units curing at the same time, and all of them identical.

Why does grout leak from a wet cast mould?

Almost always because of poorly fitted joints between panels, closures that do not clamp evenly or a base that does not seat properly. Walls bulging under the pressure of fresh concrete and opening the joints also play a part.

What information is needed to design the mould?

The drawing or a technical sample of the unit, the production system (immediate demoulding or wet casting), how the machine vibrates and compacts, the production rate and how the mould is handled in the plant.

Keep reading

More technical criteria, organised by line of work.

The blog categories help you continue by affinity: precast moulds, pipe jacking and deep drilling tools.

Industrial blog